From Fpga4u

1. Altera Quartus Ll
2. Altera Quartus Ii 9.0 Download Windows 10
3. Altera Quartus Ii Programmer Download
4. Altera Quartus Ii 9.0 Web Edition Download
5. Altera Quartus Ii 9.0 Downloadd

Quartus Prime / II Version (Standard / Subscription) Latest Supported Quartus Prime / II Version (Lite / Web) MAX 10 FPGA - Latest Release: Latest Release: MAX V - Latest Release: Latest Release: MAX II - Latest Release: Latest Release: MAX 7000 - 13.0sp1: 13.0sp1: MAX 3000A - 13.0sp1: 13.0sp1. Hello, I've recently installed Quartus II 9.0 and Modelsim-Altera (using the new installation package of 9.0), but when I tried to run.

This page will guide you through all steps needed to install all the necessary tools for Windows to use your FPGA4U at home.

• 1On Windows
  • 1.3Install USB drivers
• 2On Linux
  • 2.2Install Quartus II
  • 2.3Install USB drivers
    • 2.3.1Known issues

Altera Quartus Ll

Download the Installer

Go to the Download page of the Quartus II Web Edition here and download it.

Install Quartus II

• Execute the installer and follow the instructions until you reach Components Select.
• There, select:
  • Quartus II Web Edition software (Free)
    • Cyclone II family for FPGA4U
    • Cyclone IV E family for FPGA4U DE0
  • [Optional] ModelSim-Altera Starter edition (Free)

• Note that it is possible to add more components later on.
• At the end of the installer you can run Quartus II. (No need to open the subscription page request). But before being able to program the board you will need to install the drivers.

Install USB drivers

FPGA4U DE0

Plug your board to your computer. Windows should ask you for the location of the drivers. Select the usb-blaster folder from your Quartus install. It is generally found in C:altera{VERSION}quartusdriversusb-blaster.

FPGA4U

For the FPGA4U, the installation of the drivers may require a special procedure, because since firmware 4.2 the FPGA4U USB device implements two interfaces. The first interface emulates the official USB-Blaster of Altera and the second can be used to transfer data between your PC and the FPGA4U. When you plug your FPGA4U for the first time, Windows will detect that this is a composite device (i.e., device with multiple interfaces) and may ask for a driver for each interface. We don't want to install two drivers, but a single driver for this composite device. To do so:

1. Close any driver installation wizard popping up.
2. Go into the Device Manager (Keys Start+Break or Start -> Control Panel -> System, Hardware Tab, and Device Manager Button).
3. In the USB devices list, look for a USB Composite Device with the following id: USBVID_09FB&PID_6001&REV_0400. To get the ID of a device, right-click on it and select Properties -> Details -> Device instance id.
   • If you cannot find it and have an Unknown device or a single Altera USB-Blaster that matches the id, simply continue this tutorial with this device instead.
4. Once you found the USB Composite Device, update its driver (right-click -> Update driver...).
5. Select manually the driver to install:
   • Do not let Windows look for a driver for you.
   • Select the driver from a specific location.
   • Click on the Have Disk button.
   • Select manually the driver located typically in C:altera{VERSION}quartusdriversusb-blaster, where VERSION refers to the version of Quartus II.
   • Click Ok to install the driver.

Now when you open the Programmer in Quartus II (Tools -> Programmer), Hardware Setup... should list USB-Blaster [USB-0]. If you have trouble programming the board or to use the USB interface, try to install the last version of the firmware.

Known Issues

A conflict was reported between Quartus II version 12.0 and Windows 7 and 8 64-bit systems that makes your FPGA unrecognized. The JTAG service (necessary to communicate with the FPGA) fails to be automatically setup during the Quartus installation and results in the Programmer failing to list the connected JTAG devices. A solution is proposed in the Altera forum: http://www.alteraforum.com/forum/showthread.php?t=36775

Since Quartus II 10.0, the Web-edition is also available for Linux systems.

Download the Installer

Go to the Download page of the Quartus II Web Edition here and download it.

Install Quartus II

By executing the script, it should open a GUI similar to the Windows version. Like for windows, in the components selection dialog, make sure to select the Cyclone II family if you are using the regular FPGA4U or the Cyclone IV E for the FPGA4U DE0. Then, simply follow the instructions.

Troubleshooting

Some people experienced an error during the execution of the install script:

Apparently there is a conflict with the file libX11.so.6. Here is a simple workaround:

• Add the option --confirm to execute the install script.

• Before proceeding, in another terminal, go in the same directory than the install script and delete the file ./bin/libX11.so.6.

• Now you can proceed.

• The installer GUI should pop up.

Altera Quartus Ii 9.0 Download Windows 10

Install USB drivers

To let users use the USB-Blaster device, you need to give them the right to. On Gentoo, you must add your user to the usb group (in /etc/group) to be able to program the device. On other distributions, you need to have write access to /proc/bus/usb/bus/id.

Here is an example for Ubuntu:

Altera Quartus Ii Programmer Download

• Create a new rule file with your favorite text editor (like vim):

• Insert the following lines

• Load this new rule by typing:

Known issues

Ubuntu (9.10 and 10.04)

For older Quartus versions than 11.0, we need to patch the JTAG server to look for devices in /sys/kernel/debug/usb/devices instead of /proc/bus/usb/devices, and in /dev/bus/usb/.../.../ instead of /proc/bus/usb/.../.../.

As the former won't fit in the string placeholder of the binary file, we choose to create a soft link.

This soft link will disappear on reboot, so if you don't want to type it every time, add this line in a script or in your /etc/rc.local file (without the sudo).

Now we will use sed to replace the paths that the JTAG server is looking at. There are 2 sets of commands, one for 32-bit OS and the other one for 64-bit. Select the set corresponding to your system. If you have a doubt, it won't harm to patch both files. Before executing the commands, replace <installation path> by your installation path (e.g., /opt/altera/10.0). Note that these commands will create a backup copy of the JTAG server (jtagd.bak).

For 32-bit OS:

For 64-bit OS:

Now, if you execute

You should get something like this:

If you are on Mac OS, a solution is to use a virtual machine running Windows or Linux. You can follow the same steps as described in the On Windows or On Linux sections for Quartus and drivers installation.

Altera Quartus Ii 9.0 Web Edition Download

Altera Quartus Ii 9.0 Downloadd